Elecrow CrowPanel Advanced 10.1-inch ESP32-P4 HMI AI display, 1024×600 IPS touch screen, Wi-Fi 6.
Source: Elecrow product page , retrieved 2026-10-10. Values are transcribed as published. See Source discrepancies for apparent errors on the vendor page.
Item Value
CPU/SoC ESP32-P4 HP core RISC-V 32-bit dual-core, up to 400 MHz LP core RISC-V 32-bit single-core, up to 40 MHz System memory 768 KB L2MEM (HP), 32 KB SRAM (LP), 8 KB TCM, 32 MB PSRAM ROM 128 KB (HP), 16 KB (LP) Flash 16 MB Development environment ESP-IDF, Arduino IDE
Item Value
Size 10.1 in Resolution 1024×600 Panel IPS Touch Capacitive, single / 5-point Viewing angle 178° Brightness 400 cd/m² (typ.) Color depth 16.7M (8-bit)
Item Value
Wi-Fi 2.4 GHz Wi-Fi 6, 802.11 b/g/n Bluetooth Bluetooth 5.3 and BLE Optional Zigbee, LoRa, nRF2401, Matter, Thread, Wi-Fi HaLow
Interfaces: USB 2.0, UART, I2C, GPIO female headers, SD card holder, battery socket, speaker jack, camera header, module female headers, etc.Functions: audio amplifier, battery charge management, USB-to-UART, microphones, dual speakers, etc.
Item Value
Model BX-PH 2.0-2PWT Pins 1×2P Pitch 2 mm Dimensions (L×W×H) 8 × 8.5 × 5.6 mm Mounting SMT right angle
Control Behavior
Reset button Press to reset the device Boot button “Press and hold the power button to burn the program” (as published) Power button Switch on/off PWR LED Power on/off indication CHG LED Lithium battery charging status, low battery state
Item Value
Mounting Mounting holes all around (M3, 3.2 mm), embedded, shell assembly Operating temperature -20 to 70 °C Storage temperature -30 to 80 °C Power input 5 V / 2 A, via USB or UART terminal Dimensions 248 × 147 mm
Pin Description Connector
SPK Audio output to speakers. Mainboard has a power amplifier. PH2.0-2P PWR Power LED — RST Reset button — BOOT — — UART0-OUT Serial link to logic modules (serial comms, printing) HY2.0-4P UART1-OUT Serial link to logic modules (serial comms, printing) HY2.0-4P UART1-IN — HY2.0-4P I2C-OUT MCU-to-peripheral communication HY2.0-4P BAT Lithium battery, with charging circuit PH2.0-2P
Pinout:
Pin Direction Note
U1RXD Input Serial port 0 receive pin (as published) U1TXD Output Serial port 0 receive pin (as published) GPIO12 I/O GPIO GPIO13 I/O GPIO GPIO14 I/O GPIO 3V3 — Power supply GND — Ground reference GPIO1 I/O GPIO GPIO0 I/O GPIO GPIO2 I/O GPIO GPIO22 I/O GPIO GPIO10 I/O GPIO GPIO11 I/O GPIO BOOT — Hold, then tap RST to enter flashing mode RST — Restarts the program; also used when flashing
Chip:
Item Value
Model ESP32-H2FH4 Flash 4 MB Quad SPI SRAM 320 KB ROM 128 KB LP memory 4 KB Ambient temperature -40 to 105 °C Voltage 3.3 V BLE channel center frequency 2402–2480 MHz RF TX power -24.0 to 20.0 dBm
Patch antenna (2.4–2.5 GHz):
Item Value
Peak gain 4.33 dBi Average gain 4.0 dBi Gain range 3.59–4.33 dBi Peak efficiency 62.5% Average efficiency 57.5% Efficiency range 51.3–62.5%
Pinout:
Pin Direction Note
CE Input Module control SCK Output SPI MISO Input SPI MOSI Output SPI 3V3 — Power supply GND — Ground reference CSN Input SPI chip select IRQ Input Interrupt, active low
Chip (nRF24L01+):
Worldwide 2.4 GHz ISM band
250 kbps, 1 Mbps, 2 Mbps air data rates
11.3 mA TX at 0 dBm
13.5 mA RX at 2 Mbps
900 nA power down
On-chip voltage regulator
1.9–3.6 V supply
Patch antenna (2.4–2.5 GHz):
Item Value
Peak gain 3.74 dBi Average gain 3.66 dBi Gain range 3.45–3.74 dBi Peak efficiency 58.9% Average efficiency 55.9% Efficiency range 53.0–58.9%
Pinout:
Pin Direction Note
DIO1 I/O Configurable GPIO SCK Input SPI MISO Input SPI MOSI Output SPI 3V3 — Power supply GND — Ground reference NRESET Output Chip reset, active low DIO2 Input RF switch: low = RX, high = TX BUSY Output Status indication NSS Input SPI chip select DIO3 I/O Configurable GPIO
Antenna:
Item Value
Gain 3.5 dBi VSWR ≤ 1.9 Input impedance 50 Ω Polarization Vertical Lightning protection DC ground Cable RF1.13, 10 cm Connector IPEX-1 Weight 0.01 kg Operating temperature -40 to 85 °C
The vendor page contains apparent errors. They are kept verbatim above and should be checked against the schematic before relying on them.
ESP32-H2 U1RXD/U1TXD. Both are described as “Serial port 0 receiving pin”, though the names indicate UART1 and U1TXD is an output.Boot button. The description mentions the power button. The H2 module’s BOOT description (hold BOOT, tap RST) is the usual ESP flashing sequence.Pin directions. Several SPI and control pin directions (e.g. nRF2401 SCK as output, SX1262 NRESET and BUSY) look stated from inconsistent perspectives (host vs. module).Wi-Fi. “Wi-Fi 6” is listed alongside only 802.11 b/g/n; Wi-Fi 6 is 802.11ax.